AMAADOR ACADEMYالشهاداتالتحقق من شهادة

ABW

الاختبار النهائي — السلامة في استخدام أقراص الجلخ الكاشطة

أجب عن الأسئلة الـ28. تحتاج إلى 80% أو أكثر للنجاح. يمكنك إعادة المحاولة كلما أردت.

هذا الاختبار النهائي متاح بـالإنجليزية.

ادرس الدورة ←

السؤال 1According to HSE guidance HSG17, what are the two main ways abrasive wheels injure people?
السؤال 2In Great Britain, which regulations now contain the duty to train people who use and mount abrasive wheels?
السؤال 3A new hire shows a one-day abrasive wheels course certificate and asks to start mounting discs on the shop's grinders. What is the right response?
السؤال 4After a disc bursts on an angle grinder, a supervisor says it was just a faulty wheel. What does HSG17 say about the causes of abrasive wheel accidents?
السؤال 5A wheel is marked RE2. What does this restriction code mean?
السؤال 6A worker picks up a resin-bonded 125 mm grinding disc for his angle grinder. The label is fine but shows a use-by date that passed two months ago. What should he do?
السؤال 7Which bond type does HSG17 say should be used for wheels on hand-held grinding machines, apart from small mounted points?
السؤال 8An operator keeps finding that his wheel glazes and stops cutting on a hard steel part, so he pushes harder. What is the best explanation and fix?
السؤال 9For which of these wheels does HSG17 say the ring test is NOT practicable?
السؤال 10A fitter has just washed a vitrified wheel because it was dusty. He wants to ring test it straight away. What should he know?
السؤال 11You are setting up storage for thin resin cutting-off discs in a new workshop. Which arrangement follows HSG17?
السؤال 12During a visual check, a mechanic finds a small chip on the edge of a new 250 mm vitrified wheel. The ring test sounds fine. What should he do?
السؤال 13HSG17 explains that the stress in a wheel rises with the square of its speed. If the speed doubles, the stress becomes:
السؤال 14A 115 mm angle grinder runs at 11 000 rpm. A worker wants to fit a 230 mm disc rated 80 m/s and 6 650 rpm, removing the guard to make it fit. What is the problem?
السؤال 15A wheel is marked 1 600 rpm maximum. The grinder's rating plate shows a spindle speed of 1 800 rpm. What should the fitter do?
السؤال 16On pneumatic grinders, what does HSG17 describe as a common cause of wheel breakage?
السؤال 17With certain exceptions, what minimum flange diameter does HSG17 give for mounting an abrasive wheel?
السؤال 18A fitter mounting a vitrified wheel finds the old blotters are torn, and the new wheel came without any. A colleague suggests using the paper label as a blotter. What is correct?
السؤال 19A wheel has just been mounted on a pedestal grinder and the guard refitted. What should happen next before anyone grinds with it?
السؤال 20The nut on a bench grinder spindle feels a bit loose after tightening by hand on the spanner. A colleague offers a length of pipe to get more leverage. What is the right approach?
السؤال 21Under OSHA 29 CFR 1910.215, what is the maximum gap between the work rest and the wheel on a bench grinder?
السؤال 22The work rest on a pedestal grinder has drifted away from the wheel as it wore down. An operator wants to adjust it. When should this be done?
السؤال 23An operator sharpening a chisel on a straight pedestal grinder wheel moves to its flat side to get a better angle. What is the risk?
السؤال 24Which method of dressing an off-hand grinding wheel does HSG17 say should be forbidden?
السؤال 25A worker using a 230 V angle grinder on a construction site has no 110 V supply available. What does HSG17 say about the electrical supply?
السؤال 26A welder needs to cut a steel bracket with an angle grinder. Which set-up is safest?
السؤال 27Under the Control of Vibration at Work Regulations 2005, what is the daily exposure limit value for hand-arm vibration?
السؤال 28What does HSG17 say about eye protection for grinding?