Customize this training

Get a certificate — $16.67$5

Abrasive Wheels Safety

Abrasive Wheels Safety

Read wheel markings, check speeds, store, inspect and mount wheels correctly, set guards and work rests, and use bench and portable grinders without bursts or contact injuries.

What you will learn

  • Describe how abrasive wheels injure people and state the main legal duties and guidance that apply.
  • Read an abrasive wheel marking and choose the right wheel for the machine and the job.
  • Store, handle and inspect wheels, including the ring test, so damaged wheels are never mounted.
  • Compare wheel and spindle speeds and recognise the causes of overspeed.
  • Follow the correct mounting sequence with flanges, blotters, nut tightening and a trial run.
  • Set guards and work rests on fixed grinders and use safe operating and dressing practice.
  • Use portable grinders and cut-off machines safely and control dust, noise, vibration, sparks and eye injuries.

Modules

  1. How abrasive wheels hurt people, and the rules
  2. Wheel types, markings and selection
  3. Storage, handling and inspection
  4. Speed: the number that decides a burst
  5. Mounting a wheel correctly
  6. Fixed grinders: guards, work rests and safe use
  7. Portable grinders, cut-off saws and health

Course facts

Level
Awareness
Estimated study time
about 45 minutes
Final assessment
28 questions · Pass mark 80%
Available in
English
Price
Free. Optional verifiable certificate: $5
Last updated
Published by
AMAADOR ACADEMY

Who this course is for

Fabricators, welders, maintenance fitters, construction and demolition workers, tool-room staff, apprentices, supervisors and HSE coordinators who use, mount or manage grinding wheels and cutting-off discs.

Prerequisites

None. Useful if you already use bench, pedestal or hand-held grinders or disc cutters at work.

Course content

1. How abrasive wheels hurt people, and the rules

An abrasive wheel is made of hard grains held together by a bond. It cuts by wearing itself away. That makes it useful, and it also makes it fragile. HSE guidance HSG17 states that the risk of breakage is inherent in every abrasive wheel, however well it was made.

HSG17 names two main ways people get hurt: the wheel breaks and fragments fly out, or the person touches the running wheel. A fragment from a wheel running at 35 m/s travels at about 126 km/h; at 125 m/s, about 450 km/h (HSG17, paragraph 29). That is fast enough to kill.

The hazards of grinding and cutting with abrasive wheels.

Around those two big hazards sit others you meet every day:

  • Eyes: flying grit and hot metal particles.
  • Trapping: fingers or a workpiece pulled between the wheel and the work rest.
  • Kickback: a hand-held cutting disc that pinches in the cut and throws the machine back at the user.
  • Entanglement: loose sleeves, gloves or rags caught by the wheel.
  • Health: dust (including silica from concrete and stone), noise and hand-arm vibration.
  • Fire and explosion: sparks landing on flammable material, and fine magnesium or aluminium dust.

2. Wheel types, markings and selection

HSG17 describes an abrasive wheel as abrasive particles bonded together. The bond is the most important thing to know for safety, because it decides how the wheel behaves and how it can break.

BondLetterBehaviourTypical use
Vitrified (inorganic)VFired in a furnace: hard, strong but brittle; holds its shape; needs dressingPrecision grinding, bench and pedestal grinders
Resinoid (organic)BCured at low temperature: tough, shock-resistant, self-dressingCutting-off discs, depressed-centre grinding discs, fettling
Rubber (organic)RTough, flexibleThin cutting-off, control wheels
Shellac (organic)EFine finishFinishing work

Other parts of the specification describe how the wheel cuts:

  • Abrasive: the grain type, for example aluminium oxide (A, WA) or silicon carbide (C).
  • Grit size: a number from very coarse (4) to very fine (1200).
  • Grade: how strongly the bond holds the grain, from A (extremely soft) to Z (extremely hard).
  • Structure: porosity; a higher number means a more open wheel.

Wheels are also made in standard shapes (ISO types). You will meet Type 1 (straight wheel), Type 27 (depressed-centre grinding disc), Type 41 (flat cutting-off disc), Type 42 (depressed-centre cutting-off disc), and cup and cylinder wheels.

3. Storage, handling and inspection

HSG17 lists bad storage and rough handling among the causes of wheel breakage in service. A crack made by a drop in the store may only open up when the wheel reaches full speed on the machine.

Do

  • Store wheels in a dry room, away from extreme temperatures.
  • Use racks, bins or compartmented drawers for each type.
  • Support plain wheels on their edge in a cradle with partitions, or on a central support.
  • Lay thin organic cutting-off discs flat on a rigid horizontal surface, away from heat and moisture, so they do not warp.
  • Mark wheels with the date received and issue the oldest first.
  • Use a truck or suitable conveyor for wheels too heavy to carry.

Don't

  • Drop, bump or roll wheels (rolling only on a soft floor when there is no alternative).
  • Pile castings or tools on top of wheels.
  • Throw discs loose into a toolbox with spanners and hammers.
  • Leave wheels in a damp van or on a frozen site overnight.
  • Put blotters or packing between stacked thin discs unless supplied that way.

4. Speed: the number that decides a burst

HSG17 calls centrifugal force the ultimate cause of wheel bursts, and it rises with the square of the speed. In HSG17's words, doubling the speed increases fourfold the stress in the wheel. A small overspeed is a big increase in stress.

A wheel's speed is given two ways on its label:

  • Peripheral (surface) speed in m/s: how fast the rim moves. This is what stresses the wheel.
  • Rotational speed in rpm: revolutions per minute at the marked diameter.

They are linked by the diameter: speed (m/s) = 3.14 x diameter (mm) x rpm / 60 000. The bigger the wheel, the faster its rim moves at the same rpm.

WheelSpindle rpmRim speedTypical disc rating
115 mm11 000about 66 m/s80 m/s: OK
230 mm6 600about 79 m/s80 m/s: OK
230 mm on a 115 mm grinder11 000about 132 m/s80 m/s: far over

Worked examples. Always use the actual figures on your wheel and machine.

The last row is the classic killer. A large disc only fits a small grinder if the guard is taken off, and then it spins far beyond its rating. HSG17 (paragraph 114) states that serious, often fatal, accidents have happened when a guard is removed to allow an oversize wheel to be mounted.

5. Mounting a wheel correctly

HSG17 states that the danger of a wheel bursting is considerably increased if it is not properly mounted. The highest stresses in a running wheel are near the hole, so mounting is designed to keep clamping and driving forces away from it.

Flanges

  • With certain exceptions, every wheel is mounted between flanges at least one-third of the wheel diameter (HSG17; OSHA 1910.215(c)(1) says the same).
  • Both flanges should have the same diameter and the same recess, so they bear equally on the wheel.
  • Flanges are recessed on the side next to the wheel. Bearing faces must be true, clean and undamaged.
  • Grey cast iron is not safe for flanges. Never replace a flange with an ordinary washer, and never tighten the nut directly on the wheel.
  • Exceptions in HSG17 include mounted wheels and points, wheels with threaded inserts, plate-mounted wheels and wheels of 20 mm or less. Reinforced resin-bonded depressed-centre and cutting-off discs up to 230 mm on portable machines may be mounted between smaller flanges, and reinforced flat cutting-off wheels on petrol-engined cut-off machines between flanges of at least one-quarter of the wheel diameter (HSG17, paragraph 48).

6. Fixed grinders: guards, work rests and safe use

HSG17 gives a guard two main jobs: contain the pieces if the wheel bursts, and keep the operator from touching the wheel as far as possible. It also protects the wheel from damage and stops an oversize wheel being fitted. The guard must be strong and securely anchored: HSG17 reports accidents where weak bolts let a burst wheel throw the whole guard off the machine.

SettingHSG17 (UK)OSHA 1910.215 (US)
Guard opening on bench and pedestal grindersMinimum enclosure 270°; opening starting no more than 65° above the horizontal through the spindleExposure not over 90°, starting no more than 65° above the horizontal
Adjustable top piece (visor or tongue)Adjusted as the wheel wears to keep the opening smallGap to the wheel never more than 1/4 in (about 6 mm)
Work restAs close as possible to the wheel, adjusted often for wearMaximum opening 1/8 in (about 3 mm)

Why the work rest matters: if the gap is too wide, the workpiece or a finger can be dragged in between the rest and the wheel. HSG17 says this causes jamming, break-up of the wheel and injury. Its main cause is not adjusting the rest as the wheel wears.

7. Portable grinders, cut-off saws and health

HSG17 notes that the largest number of abrasive wheels in use are on hand-held machines, often used by people with little training. The general rules on speed, inspection and mounting apply in full, plus a few more.

PointRequirement or guidance
Wheel typeOrganic-bonded only; reinforced for cutting-off (HSG17)
GuardSecured and positioned between the user and the wheel; at least 175° enclosure for depressed-centre and cutting-off discs (HSG17); OSHA 1926.303 allows no more than 180° exposure
Guard clearanceNot more than 6 mm to the rim of an unused wheel (HSG17)
ControlsPlaced so the tool cannot start accidentally when put down
Power on construction sites110 V preferred; 230/240 V only with an RCD (HSG17)
Multiple discsNever stack discs with a spacer or glue them to make a wider cut

Do

  • Check the tool, cable, plug and guard before use.
  • Clamp the workpiece; HSG17 says lack of rigidity can lead to wheel breakage.
  • Hold the grinder with both hands, using the side handle.
  • Keep the cut straight and apply even pressure.
  • Let the disc stop before putting the tool down; unplug it to change discs.
  • Direct sparks away from people, gas cylinders and flammables.

The full lesson continues in the interactive course on this page.

Sources and references

Awareness training only. It does not make you competent to mount abrasive wheels. UK law (PUWER 1998, regulation 9) and HSE guidance HSG17 expect practical training, and your employer must decide who may mount wheels. Always follow the wheel and machine manufacturer’s instructions and your site rules.

All courses · Occupational Safety — Free courses, certificate $5 | AMAADOR ACADEMY