AMAADOR ACADEMYCertificatesVerify a certificate

ABW

Final check — Abrasive Wheels Safety

Answer the 28 questions. You need 80% or more to pass. You can retry as many times as you like.

Study the course →

Question 1According to HSE guidance HSG17, what are the two main ways abrasive wheels injure people?
Question 2In Great Britain, which regulations now contain the duty to train people who use and mount abrasive wheels?
Question 3A new hire shows a one-day abrasive wheels course certificate and asks to start mounting discs on the shop's grinders. What is the right response?
Question 4After a disc bursts on an angle grinder, a supervisor says it was just a faulty wheel. What does HSG17 say about the causes of abrasive wheel accidents?
Question 5A wheel is marked RE2. What does this restriction code mean?
Question 6A worker picks up a resin-bonded 125 mm grinding disc for his angle grinder. The label is fine but shows a use-by date that passed two months ago. What should he do?
Question 7Which bond type does HSG17 say should be used for wheels on hand-held grinding machines, apart from small mounted points?
Question 8An operator keeps finding that his wheel glazes and stops cutting on a hard steel part, so he pushes harder. What is the best explanation and fix?
Question 9For which of these wheels does HSG17 say the ring test is NOT practicable?
Question 10A fitter has just washed a vitrified wheel because it was dusty. He wants to ring test it straight away. What should he know?
Question 11You are setting up storage for thin resin cutting-off discs in a new workshop. Which arrangement follows HSG17?
Question 12During a visual check, a mechanic finds a small chip on the edge of a new 250 mm vitrified wheel. The ring test sounds fine. What should he do?
Question 13HSG17 explains that the stress in a wheel rises with the square of its speed. If the speed doubles, the stress becomes:
Question 14A 115 mm angle grinder runs at 11 000 rpm. A worker wants to fit a 230 mm disc rated 80 m/s and 6 650 rpm, removing the guard to make it fit. What is the problem?
Question 15A wheel is marked 1 600 rpm maximum. The grinder's rating plate shows a spindle speed of 1 800 rpm. What should the fitter do?
Question 16On pneumatic grinders, what does HSG17 describe as a common cause of wheel breakage?
Question 17With certain exceptions, what minimum flange diameter does HSG17 give for mounting an abrasive wheel?
Question 18A fitter mounting a vitrified wheel finds the old blotters are torn, and the new wheel came without any. A colleague suggests using the paper label as a blotter. What is correct?
Question 19A wheel has just been mounted on a pedestal grinder and the guard refitted. What should happen next before anyone grinds with it?
Question 20The nut on a bench grinder spindle feels a bit loose after tightening by hand on the spanner. A colleague offers a length of pipe to get more leverage. What is the right approach?
Question 21Under OSHA 29 CFR 1910.215, what is the maximum gap between the work rest and the wheel on a bench grinder?
Question 22The work rest on a pedestal grinder has drifted away from the wheel as it wore down. An operator wants to adjust it. When should this be done?
Question 23An operator sharpening a chisel on a straight pedestal grinder wheel moves to its flat side to get a better angle. What is the risk?
Question 24Which method of dressing an off-hand grinding wheel does HSG17 say should be forbidden?
Question 25A worker using a 230 V angle grinder on a construction site has no 110 V supply available. What does HSG17 say about the electrical supply?
Question 26A welder needs to cut a steel bracket with an angle grinder. Which set-up is safest?
Question 27Under the Control of Vibration at Work Regulations 2005, what is the daily exposure limit value for hand-arm vibration?
Question 28What does HSG17 say about eye protection for grinding?