AMAADOR ACADEMYالشهاداتالتحقق من شهادة

PRO-CEM

الاختبار النهائي — مدير طاقة معتمد (CEM) — تحضير الامتحان

أجب عن الأسئلة الـ130. تحتاج إلى 80% أو أكثر للنجاح. يمكنك إعادة المحاولة كلما أردت.

هذا الاختبار النهائي متاح بـالإنجليزية.

ادرس الدورة ←

السؤال 1In an ISO 50001 EnMS, a facility selects 'kWh per ton of product' as a metric to track performance over time. What is this metric correctly called?
السؤال 2A three-phase 480 V load draws 250 A at a power factor of 0.78 lagging. What is the approximate real power consumed?
السؤال 3A plant pays a demand charge of $14/kW based on its monthly peak 15-minute demand. A single shift starting a 200 kW chiller coincident with existing 850 kW load raises the peak. The best low-cost strategy to avoid this new peak is to:
السؤال 4Which of the following is the FIRST step required when establishing an ISO 50001 energy management system?
السؤال 5A motor system has a measured load power factor of 0.72 lagging while drawing 300 kW. To correct the power factor to 0.95, the approximate capacitive reactive power (kVAR) required is:
السؤال 6In ISO 50001, the 'energy baseline' is best described as:
السؤال 7A utility tariff has an energy charge of $0.09/kWh and a demand charge of $18/kW. A facility runs a 100 kW load for 730 hours/month. If it instead runs the same total energy (73,000 kWh) over only 200 hours/month, the demand becomes 365 kW. The change in monthly demand charge is approximately:
السؤال 8Which document framework underlies the management-system structure (Plan-Do-Check-Act) shared by ISO 50001, ISO 9001, and ISO 14001?
السؤال 9Installing fixed power factor correction capacitors at a motor terminal, while the motor is lightly loaded or idling, can cause:
السؤال 10During an ISO 50001 energy review, a facility identifies that its air compressors, chiller plant, and process ovens account for 80% of energy use. These should be designated as:
السؤال 11A facility's billed demand uses a ratchet clause: the minimum billing demand is 80% of the highest demand set in the prior 11 months. A summer peak of 1,000 kW occurred. In a winter month with actual demand of 600 kW, the billed demand will be:
السؤال 12The relationship among real power (P), reactive power (Q), and apparent power (S) in an AC circuit is best expressed as:
السؤال 13An energy manager wants to verify that energy performance improvements are real and not merely due to lower production. The most appropriate analytical approach is to:
السؤال 14A 100 hp motor (74.6 kW output) operating at 92% efficiency and 0.85 power factor draws how much apparent power (kVA) from the line at full load?
السؤال 15Within the ISO 50001 PDCA cycle, conducting an internal audit and management review of the EnMS falls under which stage?
السؤال 16A facility is offered an interruptible/curtailable rate that gives a $4/kW monthly demand credit in exchange for shedding 500 kW on request. The MOST important factor to evaluate before accepting is:
السؤال 17Improving a facility's power factor from 0.80 to 0.95 (real power unchanged) primarily reduces:
السؤال 18An energy team sets the objective 'reduce compressed-air energy by 15% within 18 months' and assigns budget, responsibilities, and timelines. In ISO 50001 terms, this documented set of actions is the:
السؤال 19Harmonic currents produced by nonlinear loads (such as variable frequency drives) most commonly cause which problem in distribution transformers?
السؤال 20A facility on a time-of-use tariff pays $0.18/kWh on-peak (12:00-18:00) and $0.06/kWh off-peak. Shifting a 50 kW batch process that runs 4 hours from on-peak to off-peak saves approximately how much per day?
السؤال 21Which statement best distinguishes 'energy efficiency' from 'demand management' for a CEM?
السؤال 22A single-phase 240 V resistive heater draws 25 A. Because it is purely resistive, its power factor and real power are:
السؤال 23A facility's regression model relates monthly electricity use to cooling degree-days (CDD). For M&V of an HVAC retrofit, the energy savings are calculated by applying the baseline regression equation to the post-retrofit period weather data and subtracting the measured post-retrofit consumption. Which IPMVP option does this represent?
السؤال 24In IPMVP terminology, what does the term 'avoided energy use' (as distinct from 'normalized savings') refer to?
السؤال 25During an energy audit you find a 100 hp motor running 6,000 h/yr at 75% load with a measured efficiency of 0.90. Electricity costs $0.10/kWh. What is the approximate annual energy cost to operate this motor? (1 hp = 0.746 kW)
السؤال 26A CHP (cogeneration) plant burns 10 MMBtu/h of natural gas fuel, producing 1,000 kW of electricity and recovering 3.4 MMBtu/h of useful thermal energy. What is the overall (total) system efficiency? (1 kWh = 3,412 Btu)
السؤال 27A CEM is selecting an M&V approach for a comprehensive retrofit involving lighting, HVAC, and controls across an entire building, where interactive effects are significant and individual sub-metering of each measure is impractical. Which IPMVP option is most appropriate?
السؤال 28A photovoltaic array is rated at 50 kW (DC, STC). Over a year it produces 70,000 kWh. What is its approximate capacity factor?
السؤال 29When developing a baseline regression model for whole-building electricity use versus outdoor temperature, which statistical indicator is most commonly used to confirm that the model adequately explains the variation in energy consumption?
السؤال 30In energy accounting, a plant's normalized 'energy use index' (EUI) is best expressed as:
السؤال 31A natural gas reciprocating engine CHP unit produces 800 kW electric and recovers heat for a process. To evaluate whether CHP is economically attractive at this site, the most important single parameter to examine is the 'spark spread', which is defined as:
السؤال 32An auditor measures a three-phase balanced load: line-to-line voltage 480 V, line current 100 A, power factor 0.85. What is the approximate real power drawn?
السؤال 33For an IPMVP-compliant M&V plan, 'non-routine adjustments' are required when:
السؤال 34A solar thermal collector receives 800 W/m2 of incident solar irradiance over an aperture area of 4 m2 and delivers 1,920 W of useful heat to water. What is its instantaneous thermal efficiency?
السؤال 35During a Level 2 (general) energy audit per ASHRAE conventions, which of the following is the auditor MOST expected to deliver that distinguishes it from a Level 1 (walk-through) audit?
السؤال 36A wind turbine has a rotor swept diameter of 50 m. Air density is 1.225 kg/m3 and wind speed is 10 m/s. Ignoring all losses, what is the theoretical maximum extractable power according to the Betz limit (59.3%)?
السؤال 37In a CHP feasibility study, the 'power-to-heat ratio' of the prime mover should ideally be matched to the site such that:
السؤال 38A facility's monthly utility bills are 'normalized' for weather to compare year-over-year performance. The preferred method of weather normalization for an energy accounting system is:
السؤال 39A 200 kW PV system under a net-metering tariff generates 260,000 kWh/yr; the building consumes 600,000 kWh/yr. Retail electricity is $0.12/kWh and the utility credits net exports at the full retail rate, but the building never exports because its load always exceeds PV output. What is the approximate annual bill savings from the PV system?
السؤال 40When measurement uncertainty in an M&V project is dominated by the precision of the regression model, the most effective way to reduce that uncertainty and increase confidence in reported savings is to:
السؤال 41A boiler stack analysis in an audit shows 6% excess oxygen and a stack temperature of 400 F. The auditor recommends reducing excess air. Primarily, lowering excess air improves combustion efficiency by:
السؤال 42A project developer compares two on-site generation options using the Levelized Cost of Energy (LCOE). LCOE is best described as:
السؤال 43An energy manager reviews continuous interval (15-minute) submeter data to verify a chiller plant retrofit using IPMVP Option B. Which is the principal advantage of Option B over Option A in this case?
السؤال 44A 1,500 kW landfill-gas reciprocating engine operates at a heat rate of 10,000 Btu/kWh (HHV). If the landfill gas has a heating value of 500 Btu/scf, approximately how much gas (scf/h) does the engine consume at full load?
السؤال 45A boiler operates with 4% O2 in the flue gas. Approximately what is the excess air level?
السؤال 46A steam trap that has failed in the open position will most directly cause:
السؤال 47Installing an economizer on a boiler recovers heat from the flue gas primarily to:
السؤال 48A project costs $50,000 and saves $20,000 per year. What is the simple payback period?
السؤال 49Which financial metric should be used to rank mutually exclusive energy projects of differing scale and lifetime?
السؤال 50Boiler blowdown is necessary primarily to:
السؤال 51A measure saves 300,000 kWh/yr at $0.10/kWh. With a 12% discount rate over 10 years (PW factor ≈ 5.65), the present worth of savings is closest to:
السؤال 52For every 40°F (22°C) reduction in stack temperature on a typical boiler, fuel efficiency improves by roughly:
السؤال 53A combined heat and power (CHP) plant achieves high overall efficiency mainly because it:
السؤال 54Insulating a bare steam line reduces standby losses chiefly by limiting:
السؤال 55Two projects: A costs $100k, saves $40k/yr; B costs $250k, saves $70k/yr. Using simple payback only, which is preferred?
السؤال 56Recovering heat from a furnace exhaust to preheat incoming combustion air is accomplished with a:
السؤال 57A deaerator in a steam system primarily serves to:
السؤال 58The levelized cost of energy (LCOE) for a generation asset is best described as the:
السؤال 59Condensate return to the boiler house is valuable because the returned water is:
السؤال 60A $200,000 retrofit yields annual savings of $35,000 and has a 15-year life with a 10% discount rate (PW factor ≈ 7.61). The benefit-cost ratio is closest to:
السؤال 61Flash steam recovered from high-pressure condensate is most usefully:
السؤال 62When comparing a high-efficiency boiler purchase, life-cycle cost analysis differs from first-cost analysis because it includes:
السؤال 63Soot deposits of 1/32 inch on boiler tubes can reduce heat transfer efficiency by roughly:
السؤال 64In NPV analysis, a project should be accepted when its net present value is:
السؤال 65Reducing boiler operating pressure to the minimum required by the process saves energy mainly by lowering:
السؤال 66A firm evaluating an ESCO performance contract is told savings are guaranteed. The financing approach where the ESCO assumes performance risk and is paid from verified savings is called:
السؤال 67A chiller plant has a measured efficiency of 0.65 kW/ton at design load. To express this in coefficient of performance (COP), which value is correct? (Use 1 ton = 3.517 kW thermal)
السؤال 68An office building uses an air-side economizer. Under which condition does the economizer provide the most 'free cooling' benefit?
السؤال 69A constant-volume AHU reheats overcooled supply air to meet zone setpoints. The single most effective energy conservation measure is typically to:
السؤال 70A facility is billed on a demand charge of $14/kW based on its monthly peak 15-minute demand. The plant's peak coincides with a single chiller starting unloaded. The best low-cost demand-reduction strategy is to:
السؤال 71A building has a measured infiltration rate that drives high winter heating loads. Which retrofit most directly reduces infiltration energy loss?
السؤال 72A customer on a time-of-use (TOU) tariff has on-peak energy at $0.22/kWh and off-peak at $0.07/kWh. The plant can pre-cool a thermal storage tank at night. The primary economic driver for thermal energy storage here is:
السؤال 73Under a typical commercial electric tariff with a ratchet clause, the demand charge for a given month may be based on:
السؤال 74A VAV box at minimum airflow still overcools a perimeter zone in winter. The most energy-efficient correction is to:
السؤال 75Scope 2 greenhouse gas emissions, as defined by the GHG Protocol, refer to:
السؤال 76A company buys unbundled renewable energy certificates (RECs) equal to its annual electricity use. Under the GHG Protocol market-based method, this primarily allows the company to:
السؤال 77A cooling tower provides condenser water to a chiller. Lowering the entering condenser water temperature (within limits) generally:
السؤال 78A demand-controlled ventilation (DCV) strategy using CO2 sensors is MOST appropriate for:
السؤال 79An energy manager evaluates a retail aggregation (deregulated) market choice. The main benefit of a fixed-price retail supply contract versus the utility default service is:
السؤال 80A 100,000 ft² building has an annual energy use of 850,000 kWh electricity plus 4,000 therms of gas. To compute a site Energy Use Intensity (EUI) in kBtu/ft²/yr, you must first:
السؤال 81For a packaged rooftop unit, raising the cooling supply-air temperature setpoint (supply-air temperature reset) during mild weather primarily saves energy by:
السؤال 82A plant operates at 0.78 lagging power factor and incurs a utility power-factor penalty. Installing correctly sized capacitors to raise PF to ~0.95 will MOST directly:
السؤال 83A heat-recovery wheel (enthalpy wheel) is added between exhaust and outdoor-air streams of an AHU. Its principal energy benefit is to:
السؤال 84A facility considers a Power Purchase Agreement (PPA) for off-site solar. A key financial attraction of a physical/virtual PPA is typically:
السؤال 85During a building audit you find both heating and cooling valves partially open on the same air handler at the same time. This 'simultaneous heating and cooling' usually indicates:
السؤال 86A water-cooled chiller's COP is 5.5 and an air-cooled alternative is 3.0. For a load requiring 500 kW of cooling, the difference in electrical input power (water-cooled vs air-cooled) is approximately:
السؤال 87A utility offers an interruptible/curtailable rate with a credit for load that can be shed on request. This rate is most attractive to a facility that:
السؤال 88In an IPMVP-based measurement and verification plan for an HVAC retrofit, the role of routine and non-routine adjustments to the baseline is to:
السؤال 89A plant's compressed air system has an artificial demand caused by running header pressure at 110 psig when end-use equipment only requires 80 psig. Approximately how much does every 2 psi reduction in operating pressure reduce compressor energy (rule of thumb)?
السؤال 90A centrifugal pump runs at 1750 rpm delivering 400 gpm at 100 ft head, drawing 15 hp. If a VFD slows it to 1400 rpm, what is the approximate new shaft power, per the affinity laws?
السؤال 91An air leak through a 1/4-inch orifice at 100 psig can waste a substantial amount of compressed air. The single most cost-effective measure for most plants to address leaks is to:
السؤال 92A throttled centrifugal fan delivers required airflow by partially closing a discharge damper. The most energy-efficient way to reduce flow on this fan over a wide turndown range is to:
السؤال 93A 100 hp standard-efficiency motor (91.0%) operating 6000 h/yr is being replaced by a NEMA Premium motor (94.5%). With electricity at $0.10/kWh, approximately what are the annual energy savings (1 hp = 0.746 kW)?
السؤال 94In a multi-compressor plant, several rotary screw compressors run partially loaded in modulation control, giving poor part-load efficiency. The recommended strategy to improve overall system efficiency is to:
السؤال 95Adding receiver (storage) capacity to a compressed air system primarily benefits the system by:
السؤال 96A pumping system is grossly oversized: a control valve is throttled to roughly 40% open at all times, dropping significant head. Besides a VFD, the most direct mechanical fix to cut energy is to:
السؤال 97Using heat of compression recovery, a 100 hp air compressor can typically recover for useful heating (space or water) approximately what fraction of its electrical input energy?
السؤال 98A 50 hp motor is loaded to only 30% of rated load for most of the year. From an efficiency standpoint, the issue with this is that:
السؤال 99When deciding whether to repair (rewind) or replace a failed motor with a NEMA Premium unit, a key consideration is that rewinding typically:
السؤال 100A facility uses compressed air at 100 psig to drive blow-off nozzles for parts drying and to operate a vacuum venturi for material handling. The best low-cost improvement is to:
السؤال 101The brake horsepower of a pump moving 600 gpm of water against 120 ft of total head at 75% pump efficiency is approximately (BHP = gpm x ft x SG / (3960 x eff)):
السؤال 102A cooling tower fan and condenser water pump are oversized and run continuously at full speed. Applying VFDs and resetting condenser water temperature based on load mainly improves efficiency because:
السؤال 103An induction motor's slip at full load is 3%. If the supply is 60 Hz and the motor is 4-pole (synchronous speed 1800 rpm), the approximate full-load speed is:
السؤال 104A compressed air audit finds the system pressure dew point is +50 F, but a critical process requires -40 F dew point only at one machine. The most energy-efficient solution is to:
السؤال 105For a fan or pump system, the single highest-leverage step before applying a VFD or trimming the impeller should be to:
السؤال 106A motor draws 480 V, 3-phase, 100 A, at a power factor of 0.80. Its approximate real power input is (P = 1.732 x V x I x PF):
السؤال 107A plant measures compressed air specific power and finds 22 kW per 100 cfm, well above the best-practice benchmark for a lubricated rotary screw plant of roughly 18 kW/100 cfm. This gap most likely indicates:
السؤال 108Two identical pumps each rated 500 gpm are piped in parallel to a single system curve. Because of the steep system curve, operating both pumps together delivers only about 750 gpm total rather than 1000 gpm. This illustrates that:
السؤال 109A measurement and verification plan under IPMVP for a VFD retrofit on a pump compares pre- and post-retrofit energy using regression against production flow. This adjusts for changing conditions and is essential because:
السؤال 110A 400 W high-pressure sodium (HPS) high-bay fixture with an 80 W ballast loss is replaced by an LED high-bay that draws 150 W total and delivers equivalent maintained illuminance. The fixtures operate 6,000 hours per year and electricity costs $0.11/kWh. What is the approximate annual energy cost saving per fixture?
السؤال 111Which lighting control strategy reduces electric lighting power in response to available natural light from windows or skylights?
السؤال 112A facility upgrades from T12 fluorescent lamps with magnetic ballasts to T8 lamps with electronic ballasts. Besides higher lamp efficacy, what additional benefit most directly reduces energy consumption?
السؤال 113The luminous efficacy of a light source is best expressed in which units?
السؤال 114An open office is illuminated to 50 footcandles, but the design task requirement is only 35 footcandles. The dimmable LED system can be reduced to match the task level. This control strategy is known as:
السؤال 115In the lumen method for interior lighting design, the average maintained illuminance equals (lamps × lumens per lamp × CU × LLF) divided by which quantity?
السؤال 116Which of the following is included in the Light Loss Factor (LLF) used to determine maintained illuminance?
السؤال 117A warehouse aisle uses occupancy sensors to switch high-bay LEDs to 20% output when unoccupied and full output when occupied. Aisles are occupied only 30% of the operating hours. Compared with leaving fixtures at full output, the approximate lighting energy reduction in the aisle is:
السؤال 118For a space requiring excellent color rendering of merchandise, which lamp characteristic is the primary selection criterion?
السؤال 119An office retrofit replaces three-lamp parabolic troffers (96 W each, with one lamp delamped and a reflector added) — reducing connected load. A delamping retrofit is most appropriate when:
السؤال 120A lighting power density (LPD) limit in energy codes such as ASHRAE 90.1 is expressed in which units?
السؤال 121A 250 W metal halide lamp (rated 20,000 lumens initial) has dropped to 13,000 lumens at the end of its maintenance period. The approximate lamp lumen depreciation (LLD) factor to apply is:
السؤال 122In a parking garage, the most cost-effective lighting control combination to maximize savings while maintaining safety is typically:
السؤال 123A passive infrared (PIR) occupancy sensor is generally LEAST suitable for which application, where ultrasonic or dual-technology sensors are preferred?
السؤال 124A demand-management program limits a building's peak demand. Which lighting-based measure can contribute to automated demand response (ADR)?
السؤال 125A retrofit replaces 1,000 fixtures, each reduced from 192 W to 110 W. The plant runs 8,760 hours/year. At $0.10/kWh, what is the approximate annual energy cost saving (ignoring HVAC interaction)?
السؤال 126In air-conditioned spaces, an efficient lighting retrofit produces a secondary energy benefit. What is it?
السؤال 127A facility evaluates an LED retrofit costing $80,000 that saves $32,000 per year. Using the simple payback method, the payback period is:
السؤال 128Which statement about LED drivers in dimmable lighting controls is correct for ensuring compatibility?
السؤال 129An auditor benchmarks a 100,000 ft² office at an installed LPD of 1.2 W/ft². If the lighting operates 3,000 hours/year, what is the approximate annual lighting energy use?
السؤال 130When performing measurement and verification (M&V) of a lighting retrofit under IPMVP, isolating the lighting circuits and metering before/after most closely corresponds to which option?