IOGP Life-Saving Rules
Apply the nine IOGP Life-Saving Rules on site: know the behaviours behind each rule, run a start-work check, use Stop Work Authority and respond fairly when a rule is broken.
What you will learn
- Explain why IOGP created the Life-Saving Rules, how the nine rules are written and how a start-work check uses them
- Apply the Work Authorization and Bypassing Safety Controls rules before and during a job
- Apply the Energy Isolation and Confined Space rules, including zero-energy checks, gas testing, attendants and rescue
- Apply the Hot Work and Working at Height rules, including ignition control, fall protection and dropped objects
- Apply the Safe Mechanical Lifting and Line of Fire rules to keep people away from loads and released energy
- Apply the Driving rule: seat belts, speed, phones, fatigue and journey management
- Use Stop Work Authority, carry out supervisor duties and respond to a rule breach with a fair, just-culture approach
Modules
- Why the Life-Saving Rules exist
- Work authorization and bypassing safety controls
- Energy isolation and confined space
- Hot work and working at height
- Safe mechanical lifting and line of fire
- Driving
- Stop work, supervisors and a fair response to breaches
Course facts
- Level
- Awareness
- Estimated study time
- about 45 minutes
- Final assessment
- 28 questions · Pass mark 80%
- Available in
- English, Français, العربية
- Price
- Free. Optional verifiable certificate: $5
- Last updated
- Published by
- AMAADOR ACADEMY
Who this course is for
Workers, contractors, supervisors and HSE staff in oil and gas, drilling, construction and energy sites, onshore and offshore, in the GCC, North Africa, Europe and worldwide.
Prerequisites
None. Basic familiarity with an industrial worksite and with permits to work is helpful.
Course content
1. Why the Life-Saving Rules exist
IOGP (the International Association of Oil & Gas Producers) collects incident data from its member companies every year and publishes it in its safety performance indicator reports. When IOGP looked at the fatal incidents behind those numbers, the same activities came up again and again: vehicles, lifting, isolation, entry into tanks and vessels, hot work, falls and people standing in the wrong place.
From that analysis IOGP published its first set of Life-Saving Rules in February 2012, with updated icons in April 2013 (18 rules: 8 core and 10 supplementary). In 2018 it revised them, using about ten more years of fatality data, and cut them to nine simpler rules written from the worker's point of view. IOGP asks companies to adopt the set without changing the wording or icons, and encourages them to manage other risks by other means rather than adding their own rules to it, so that a worker moving between operators and contractors meets the same rules everywhere.
The nine IOGP Life-Saving Rules (2018), listed alphabetically. Emojis here are teaching aids, not the official IOGP icons.
2. Work authorization and bypassing safety controls
A permit to work is how a site controls non-routine or high-risk jobs: who does what, where, with which hazards removed and which precautions in place. The Work Authorization rule makes the worker part of that system, not just a name on the form.
I will (paraphrased)
- Check whether my job needs a permit before I start.
- Make sure I am authorized to do the work.
- Understand what the permit says, including its limits and precautions.
- Confirm at the job that the hazards are controlled and it is safe to start.
- Stop and reassess if the job or the conditions change.
I will not
- Start on a verbal "go ahead" when the site requires a permit.
- Work outside the area, time or scope written on the permit.
- Sign a permit I have not read or a field check I have not done.
- Carry on after a change without a new check.
Changes are where permits fail most: a shift handover, a second crew, a job that turns out bigger than planned, a gas alarm nearby. A permit only describes the situation at the moment it was issued.
3. Energy isolation and confined space
Hazardous energy is anything that can move, burn, crush, shock or spray when you open up equipment: electricity, pressure in liquids and gases, stored springs, raised loads, hot fluids, chemicals and moving parts. Most isolation accidents happen because one source was missed, an isolation was not locked, or nobody checked that the energy was really gone.
Look for every type of energy, not just the obvious one.
Paraphrased, the rule asks you to say:
- I have identified every energy source — using drawings, the isolation certificate and a walk of the system.
- I have confirmed the hazardous sources are isolated, locked and tagged — with my own lock where the site uses personal locks.
- I have checked for zero energy — try the start button, read the gauge, open the bleed, test for voltage.
- I have tested for residual or stored energy — trapped pressure between valves, charged capacitors, springs, hydraulic accumulators, liquid in low points.
Isolation methods have different strengths. For hydrocarbons, a single closed valve is weaker than a double block and bleed, which is weaker than a positive isolation with a spade or spool removed. Your site's isolation standard says which is needed; the rule asks you to confirm it is actually there.
4. Hot work and working at height
Hot work is any work that can create a flame, spark or hot surface able to ignite a flammable atmosphere: welding, cutting, grinding, brazing, some drilling, and using non-certified electrical tools in a hazardous area. On a hydrocarbon site the fuel is often already present; the hot work supplies the last side of the fire triangle.
I will (paraphrased)
- Identify and control ignition sources, including smoking and phones where they are banned.
- Before hot work, confirm flammable material has been removed or isolated.
- Get authorization before starting any hot work.
- In a hazardous area, confirm a gas test has been done and gas will be monitored continually.
I will not
- Weld on or near a tank, drum or line that has not been cleaned, isolated and gas tested.
- Start without the fire watch and extinguisher in place.
- Carry on when a gas alarm sounds or the wind changes.
Typical controls on a hot work permit: gas test before and during the work (in a hazardous area the rule itself asks for continuous monitoring), removing or covering combustibles, sealing drains and openings, fire blankets and screens for sparks, a dedicated fire watch who stays after the job ends, and checking connected equipment — vapour can travel through a pipe from a tank you cannot see.
5. Safe mechanical lifting and line of fire
Cranes, hoists, forklifts, winches and the slings and shackles they use move heavy loads over and around people every day. When a lift goes wrong the energy involved is huge: a dropped, swinging or toppling load rarely gives a second chance.
I will (paraphrased)
- Confirm the lifting equipment and the load have been inspected and are fit for the lift.
- Only operate lifting equipment I am qualified and authorized to use.
- Set up barriers and exclusion zones, and respect them.
- Never walk or stand under a suspended load.
I will not
- Use a sling with no tag, a damaged eye or an unknown working load limit.
- Guide a load with my hands on it when a tag line can do the job.
- Lift in wind or visibility outside the limits of the lift plan.
- Plan — lift category, weight, centre of gravity, radius and crane capacity; a written lift plan for complex or critical lifts.
- Check — certification and pre-use inspection of crane and rigging; load secured, no loose items on top.
- Brief — one appointed signaller, agreed signals, everyone knows the exclusion zone.
- Lift — take the weight slowly, test, then move; tag lines, never hands, to control swing.
- Land — on prepared ground or dunnage, slings slack before anyone approaches.
6. Driving
For years, motor vehicle incidents have been one of the leading causes of death in IOGP member companies' safety data, onshore operations in particular. Workers drive long distances between camps, rigs and towns, often on desert tracks or busy highways, often tired at the end of a long shift. That is why driving has its own rule.
Five behaviours that the Driving rule asks of every driver.
I will (paraphrased)
- Always wear my seat belt, and make sure my passengers wear theirs.
- Stay within the speed limit and slow down further for road, weather and load conditions.
- Not use a phone or operate other devices while driving.
- Only drive when I am fit, rested and fully alert.
- Follow the journey management plan.
I will not
- Answer "just one" call or message while the vehicle is moving, even hands-free if company policy bans it.
- Drive after a night shift when I am fighting to keep my eyes open.
- Change route or travel at night without updating the journey manager.
Many companies add their own driving standards on top: in-vehicle monitoring systems, defensive driving training, vehicle inspections, rest-break rules and bans on night driving in remote areas. These come from IOGP's land transportation guidance (Report 365) and from national law. The rule focuses on the five behaviours that most often decide whether a crash is survivable or happens at all.
7. Stop work, supervisors and a fair response to breaches
Every Life-Saving Rule ends in the same place: if the controls are not in place, the work does not start. IOGP is direct about it. Do not start an activity until you can confirm that the actions in the rule can be followed. If a rule cannot be followed once the job is under way, stop the job, call your supervisor and reassess the risk. Report 459 also expects everyone to be empowered and encouraged to stop work and intervene when they see a rule being broken or any other unsafe situation.
Five steps of a stop-work intervention.
Most companies call this Stop Work Authority (SWA): any worker, contractor or visitor can stop a job they believe is unsafe, without asking permission first and without fear of blame. It covers your own task and other people's.
- Stop — say clearly "Stop the job" and use the agreed signal; make sure the crane, machine or vehicle really stops.
- Make safe — only if you can do it without creating a new risk: step back, keep people out, use only controls you are authorized to operate.
- Talk — explain what you saw and listen. The crew may know something you do not, or the other way round.
- Report — tell the supervisor and record the stop so the site can learn from it.
- Restart only when fixed — the gap is closed, the start-work check is repeated and the supervisor agrees.
The full lesson continues in the interactive course on this page.
Sources and references
- IOGP Life-Saving Rules (Report 459 and supporting material)
- Report 459 Life-Saving Rules – free download (IOGP bookstore)
- IOGP Data Series – safety performance indicators
- Valero Delaware City refinery nitrogen asphyxiation incident (2005)
- The Public Inquiry into the Piper Alpha Disaster (Cullen Report)
- Confined spaces – OSHA safety and health topic
- Hearts and Minds toolkit – Making compliance easier (formerly Managing rule breaking)
Unofficial awareness course. It is not produced, reviewed or endorsed by IOGP. The rule behaviours are paraphrased for teaching; for the official wording and icons, use IOGP Report 459 as adopted by your company. This course does not replace site induction, permit-to-work training, confined-space, lifting, working-at-height or driving training, practical assessment or your employer's written authorization.
All courses · Occupational Safety — Free courses, certificate $5 | AMAADOR ACADEMY