Load Securing on Road Vehicles
Understand the forces acting on a load, choose blocking or lashing, check straps and chains, and load, check and unload trucks and vans so nothing shifts, falls or crushes anyone.
What you will learn
- Explain why loads move and state the forces securing must resist and who is responsible.
- Check that the vehicle and its body suit the load and plan weight distribution before loading.
- Choose and combine blocking, direct lashing, top-over lashing and friction correctly.
- Read lashing labels and inspect straps, chains and accessories, rejecting damaged ones.
- Apply suitable securing to common loads: pallets, machinery, coils, long items and vans.
- Recheck loads on the journey, unload safely and know how roadside inspections classify defects.
Modules
- Why loads move, and who answers for it
- The right vehicle and a load plan
- Securing methods: blocking, lashing and friction
- Straps, chains and accessories
- Securing common loads
- On the road, at delivery, and at the roadside check
Course facts
- Level
- Awareness
- Estimated study time
- about 45 minutes
- Final assessment
- 24 questions · Pass mark 80%
- Available in
- English, Français, العربية
- Price
- Free. Optional verifiable certificate: $5
- Last updated
- Published by
- AMAADOR ACADEMY
Who this course is for
Truck and van drivers, loaders, warehouse and dock staff, shippers, transport planners, supervisors and HSE coordinators in logistics, construction, industry and distribution.
Prerequisites
None. Basic reading ability in the course language. Some experience around vehicles or loading docks helps.
Course content
1. Why loads move, and who answers for it
A load has no brakes. When the vehicle brakes hard, the load wants to carry on forwards at the speed it had. When the vehicle turns, the load wants to go straight on, so it pushes towards the outside of the bend. When the vehicle accelerates or goes over a bump, the load pushes backwards or lifts for a moment. Weight alone does not hold it: a heavy load moves just as easily as a light one, and hits harder.
For this reason European law states how much force the securing must resist. Directive 2014/47/EU, Annex III, used for roadside inspections in all EU countries, requires securing to withstand at least:
| Direction | Force to resist | Typical cause |
|---|---|---|
| Forwards | 0.8 × the weight of the load | Emergency braking |
| Sideways (each side) | 0.5 × the weight | Bends, roundabouts, swerving |
| Backwards | 0.5 × the weight | Accelerating, uphill starts |
It must also prevent the load from tilting or tipping. The detailed calculation method is in the standard EN 12195-1. In the United States, 49 CFR 393.102 uses the same 0.8 / 0.5 / 0.5 values. In Great Britain, the DVSA code of practice is the reference; check its current wording for the forward figure.
2. The right vehicle and a load plan
Before any strap goes on, ask what the vehicle itself can hold. Annex III of Directive 2014/47/EU says that when the headboard, sides, rear doors, stanchions or lashing points are used to secure cargo, their strength requirements must be taken into account. The main standards are:
| Part | Standard | What to check |
|---|---|---|
| Body structure (headboard, sides, rear) | EN 12642 (code L or XL) | The body’s rating and certificate. An XL body is tested to hold more of the load than a standard L body. |
| Lashing points | EN 12640 | Number, condition and rated strength. Never load a point beyond its rating. |
| Tarpaulins and curtains | EN 12641 | Weather protection unless the body is certified to restrain cargo. |
| Swap bodies, containers | EN 283, ISO 1496 | Rated walls and lashing rings. |
Curtainsiders: DVSA guidance states that most curtains are designed for weather protection only, so the load needs its own restraint. The exception is an XL-certified curtainsider loaded to a “positive fit”: the load fills the bed from the headboard, side gaps are small (DVSA cites 80 mm or less) and the rear is secured. If those conditions are not met, treat it as a standard curtainsider and lash the load.
3. Securing methods: blocking, lashing and friction
Annex III of Directive 2014/47/EU lists four restraining methods, used alone or combined: locking, blocking (local or overall), direct lashing and top-over lashing.
| Method | How it works | Examples |
|---|---|---|
| Locking | A mechanical lock joins the load to the vehicle | Container twist-locks |
| Blocking | The load rests against something solid that takes the force | Headboard, rated side walls, stanchions, wedges, chocks, beams, filling gaps with dunnage or airbags |
| Direct lashing | Straps or chains run from the load to the vehicle and take the force in tension | Diagonal lashing of a machine, spring lashing |
| Top-over lashing | Straps pressed over the load increase friction on the floor | Pallets, crates, stacks of boards |
Blocking is the first choice wherever it is possible. A load placed tight against a rated headboard cannot gain speed, so it needs much less lashing. Gaps are the enemy: fill them with empty pallets, timber, or airbags designed for load securing.
Friction always helps and should be maximised. A clean, dry floor is better than a wet, oily or dusty one. Anti-slip mats under the load raise friction strongly; EN 12195-1 gives friction values for common material pairs and for anti-slip mats. But friction alone is not securing: on bumps and with vibration the load can briefly lift and friction falls close to zero. The European Best Practice Guidelines warn against relying on the weight of the load to keep it in place.
4. Straps, chains and accessories
Web lashings made of man-made fibres are covered by EN 12195-2. Each one carries a label that tells you what it can do. No label, or a label you cannot read, means the strap must not be used.
| Marking | Meaning | Used for |
|---|---|---|
| LC (lashing capacity), in daN | Maximum force the lashing may take in straight pull | Direct lashing |
| STF (standard tension force), in daN | Tension reached in the strap when the ratchet handle is pulled with the standard hand force | Top-over lashing |
| SHF (standard hand force) | The hand force on the ratchet used to measure STF: 50 daN | Shows the ratchet is meant for normal hand effort |
| Material and length | Polyester, polyamide, polypropylene; length in metres | Choosing the right strap for the load and chemicals |
A unit of 1 daN (decanewton) is close to the force of 1 kg. A strap with LC 2,500 daN can hold roughly 2.5 tonnes in a straight pull; a typical STF of a few hundred daN is what it actually presses down in top-over lashing.
5. Securing common loads
Palletised goods are the most common load. The pallet must first be a stable unit: goods well stacked, stretch-wrapped or strapped to the pallet, no overhang. A pallet that falls apart cannot be secured by any number of straps over the top.
- Check the unit — sound pallet, wrapped load, no crushed or leaning stacks.
- Load tight — against the headboard and side by side; fill any gap with empty pallets or airbags.
- Add friction — anti-slip mats under pallets on smooth floors.
- Secure — top-over straps with edge protectors, or blocking bars and rated walls, as the plan requires.
- Secure the rear — the last row needs its own restraint if the doors are not rated.
Vans and light commercial vehicles are often forgotten. The European Best Practice Guidelines, built on EN 12195-1, focus on vehicles over 3.5 tonnes; for vehicles up to 3.5 tonnes, other standards such as ISO 27956 (cargo securing in delivery vans) may apply. The physics is the same: in a crash or hard stop, loose tools and boxes fly forwards into the cab. INRS crash tests on light commercial vehicles show how dangerous unsecured loads and an unbelted driver are, even at low speed.
6. On the road, at delivery, and at the roadside check
Straps and chains lose tension as the load settles and vibrates. The DVSA code asks drivers to recheck restraints during the journey, especially after harsh braking or swerving and with loads that settle, such as sand or aggregate. US rules are precise: 49 CFR 392.9 requires truck drivers to inspect cargo and securement within the first 50 miles (about 80 km), then again after any change of duty status, 3 hours of driving or 150 miles, whichever comes first.
- Stop somewhere safe — a lay-by or parking area, hazard lights on, high-visibility clothing.
- Walk round — look for slack straps, moved items, bulging curtains, leaning stacks.
- Re-tension — from the ground, using the ratchet by hand.
- If the load has moved — do not continue if it is unsafe. Call the operator; get help to re-secure or transfer it.
Opening a curtain or door is a danger point. A load that shifted during the trip may be leaning against the curtain or door. Look first: a bulging curtain or door under pressure is a warning. Stand to the side, open slowly, and never stand under or in front of a load that may fall.
The full lesson continues in the interactive course on this page.
Sources and references
- Directive 2014/47/EU on technical roadside inspections (Annex III: cargo securing)
- Securing loads on HGVs and goods vehicles (code of practice)
- L’essentiel sur l’arrimage des charges (ED 6145, outil 40)
- European Best Practice Guidelines on Cargo Securing for Road Transport (2014)
- 49 CFR Part 393 Subpart I: Protection against shifting and falling cargo
- Load security (logistics)
- Stone company fined £50,000 after worker fatally struck by falling granite slabs
- Electrical wholesaler fined £4million after worker’s crush injuries mean he now needs 24/7 care
Awareness training only. It does not replace your employer’s risk assessment, load plans, site rules or practical training on your vehicle and equipment, nor certified calculations under EN 12195-1. Forklift, crane and lorry-loader operation need separate authorisation. Always check the rules in force in your country.
All courses · Occupational Safety — Free courses, certificate $5 | AMAADOR ACADEMY